Menu

Portable network taps with filter function and remote management

Network Test Access Points (TAPs) are hardware tools that let you monitor your network. Filtering TAPs allows you to filter out the traffic that is not needed by the tool to perform its function.

Supports Tap 'Breakout', Aggregation, Regeneration / SPAN and Filter modes.

Filtering + aggregation ensures that monitoring ports are not oversubscribed with unneeded data. Filter TAPs are specially designed hardware devices that let you see every bit, every byte and every packet.®

  • Easy remote access and management with GUI / CLI card
  • Set usage alerts to avoid over-subscription
  • Filter and aggregate to monitoring / analysis tools
  • Supports Tap 'Breakout' aggregation, regeneration / SPAN and filter modes
  • Copper TAPs support Link Speed Synchronization
  • Supports jumbo frames
  • 100% safe and invisible; no IP address, no MAC address; can not be hacked
  • 1U rack mount accommodates up to 4 portable TAPs
  • Tested and certified
  • Made, tested and supported in the USA

Portable copper network TAPs with filter function

TAP options
Model No. Medi Modes Features Remote Management
Network Monitor Breakout Aggregation Regeneration Filtering
P1GCCFE  2x 1GbE Copper 2x Copper-RJ45 Yes Yes Yes Yes Link Sync with Fail Safe Yes
P1GCSFE  2x 1GbE Copper 2x SFP Yes Yes Yes Yes Link Sync with Fail Safe Yes

Multimode SX Gigabit Network Taps with filter function

TAP options
Model No. Media Modes Features Remote Management
Network Monitor Breakout Aggregation Regeneration Filtering
P1GMCFE  2x 1GbE LC 2x Copper-RJ45 Yes Yes Yes Yes Passive Yes
P1GMSFE  2x 1GbE LC 2x SFP Yes Yes Yes Yes Passive Yes



Singlemode LX Gigabit Network Taps with Filter Function

TAP options
Model No. Media Modes Features Remote Management
Network Monitor Breakout Aggregation Regeneration Filtering
P1GSCFE  2x 1GbE LC 2x Copper-RJ45 Yes Yes Yes Yes Passive Yes
P1GSSFE  2x 1GbE LC 2x SFP Yes Yes Yes Yes Passive Yes
Diagramm
Breakout mode
Diagramm
Aggregation mode
Diagramm
Regeneration / SPAN mode
Diagramm
Filtering
  • Filtering on OSI Layer 2-4 (TCP, UDP, IP, etc.)
  • 100% Passive, no impact on active network line
  • Plug'n Play simple installation without configuration
  • Layer 1 & amp; 2 errors including CRC / FCS errors are rejected
  • Flexible media conversion on the monitoring ports through SFP interfaces
  • High availability redundant power
  • Transparent and invisible in the network (no MAC address)
  • Diode technology prevents interference with the active network
  • Network Taps Available from 10Mbps to 100Gbps Network Lines
  • Link Speed ​​Synchronization & amp; Link Fault Propagation
  • Supports jumbo frames up to 16,383 bytes
  • Full-duplex monitoring without packet loss
  • Fiber Taps available at 50:50, 60:40, 70:30, 80:20, 90:10 Split Ratios
  • Permanent access without data stream interference
  • 4 functions (break-out, aggregation, injection and bypass) in one module



    Rohs

Modular Chassis Systems for Aggregation Taps with Filter Function on OSI Layer 2-4

Garland Technology offers Modular Chassis Systems in two versions, one of which allows the installation of 4 modules in a 19 "height unit, the other allows you to use 12 modules in 2U.The available modules are classic network taps, aggregation taps, bypass taps (switches The modules can be combined with each other, parallel use of different modules is also supported.The chassis systems are equipped with a management port, which allows you to configure the modules.The standard equipment of the chassis also includes redundant power supply units , which are available both for operation in the AC and in the DC environment.You get a carrier grade system for a small price!

Port-to-Port Aggregator with Port Mapping Filtering

Network Test Access Points (TAPs) are hardware tools that let you access and monitor your network. The modular package broker chassis system provides a flexible and scalable design to meet your networking needs today and tomorrow.

Filtering network TAPs allows you to filter the traffic that is not needed by the tool to perform its function. The port-to-port aggregation feature in the 1G Modular Chassis combines filtering and aggregation functionality to ensure that the connections are aggregated. The filtering ensures that listening ports are not oversubscribed with unsolicited data.

Design your own chassis with modular TAPs that support tap-breakout, aggregation, filtering, regeneration / SPAN, and bypass modes. With this modular system, you can fully deploy and manage your monitoring and security applications, and ensure 100% network availability so you can see every bit, every byte and every packet.

  • Scalable modular TAP system
    • 2U accommodates up to 12 TAPs - backplane filtering within the TAP range
    • 1U contains up to 4 TAPs - backplane filtering between TAPs and port
  • Management and non-management options:
    • Management Card: Ethernet with GUI - and - Serial with CLI controller
    • Chassis without management available; (Administrative card can be added at a later date)
  • Port Mapping: The filter grants granular network traffic selection on layers 2, 3, and 4 of the packet to provide monitoring tools only for the traffic they are protecting
  • Multi-level filter support: MAC, VLAN, IP, DSCP, TCP, UDP
  • Network Failsafe detects power failures and closes the relay circuits automatically in less than 8 milliseconds. Then the two network devices connected to ports A and B are reconnected
  • Media Conversion: Glass fiber (SX, LX, ZX) to copper (TX) or copper (TX) to glass fiber (SX, LX, ZX). Short range fiber (SX) to long range fiber (LX or ZX)
  • TAP modules are hot-swappable, fully configurable, and interchangeable
  • Fits GT Legacy Modular TAPs
  • Two internal AC or DC power supplies
  • Supports jumbo frames and passes physical errors
  • Packet Slicing and Packet Injection (Aggregate Mode for Copper Network Port TAPs)
  • 100% safe and invisible; no IP address, no MAC address; can not be hacked

Chassis options
Model No. Chassis/TAPs* Power Supplies Dimensions (WxHxD)
M1G1ACE

1U; up to 4 TAPs

Dual Internal AC 17.40” x 1.75” x 13.45”
(441.96mm x 44.45mm x 341.63mm)

M1G1DCE

1U; up to 4 TAPs

Dual Internal DC

M1G2ACE

2U; up to 12 TAPs

Dual Internal AC 17.40” x 3.47” x 13.45”
(441.96mm x 88.14mm x 341.63mm)

M1G2DCE

2U; up to 12 TAPs

Dual Internal DC

M1GC

Management card: Ethernet/GUI - and- Serial/CLI for M1GxxE

Copper network TAP modules with filter function

TAP options
Model No. Media Modes Features Remote Management
Network Monitor Breakout Aggregation Regeneration Filtering
M1GCCF  2x 1GbE Copper 2x Copper-RJ45 Yes Yes Yes Yes Link Sync with Fail Safe Yes
M1GCSF  2x 1GbE Copper 2x SFP Yes Yes Yes Yes Link Sync with Fail Safe Yes

Multimode SX Gigabit Network TAP modules with filter function

TAP options
Model No. Media Modes Features Remote Management
Network Monitor Breakout Aggregation Regeneration Filtering
M1GMCF  2x 1GbE LC 2x Copper-RJ45 Yes Yes Yes Yes Passive Yes
M1GMSF  2x 1GbE LC 2x SFP Yes Yes Yes Yes Passive Yes



Singlemode LX Gigabit Network TAP Module with Filter Function

TAP options
Model No. Media Modes Features Remote Management
Network Monitor Breakout Aggregation Regeneration Filtering
M1GSCF  2x 1GbE LC 2x Copper-RJ45 Yes Yes Yes Yes Passive Yes
M1GSSF  2x 1GbE LC 2x SFP Yes Yes Yes Yes Passive Yes
Diagramm
Breakout mode
Diagramm
Aggregation mode
Diagramm
Regeneration / SPAN mode
Diagramm
Filtering

646
656_2

  • 100% passive, no impact on the active network line
  • Plug'n Play easy installation without configuration
  • Layer 1 & 2 errors including CRC errors are rejected
  • Media conversion on the monitoring ports through SFP interfaces
  • Redundant power supply for high availability
  • Diode technology prevents interference in the active network
  • Network Taps available from 10Mbps to 100Gbps network cables
  • Link Speed Synchronization
  • Link Fault Propagation
  • Supports jumbo frames up to 16,383 bytes
  • Full duplex monitoring without packet loss
  • Fiber Taps with different split ratios available (50:50, 60:40, 70:30, 80:20, 90:10)
  • Permanent access without data stream interference
  • 4 functions (break-out, aggregation, injection and bypass) available in one module



Rohs

We are happy to advise you and look forward to hearing from you!

NEOX - Location

Our partners

IT Security made in Germany TeleTrusT Quality Seal


Contact Details

NEOX NETWORKS GmbH
Otto-Hahn Strasse 8
63225 Langen / Frankfurt am Main
Tel: +49 6103 37 215 910
Fax: +49 6103 37 215 919
Email: info@neox-networks.com
Web: http://www.neox-networks.com
Your route to us >>